BÌNH TẠO BỌT CHUYÊN DỤNG CẦM TAY Venus Super Foamer HD TÍNH KIỀM
LÀ Máy tạo bọt có dung tích 2L. Phù hợp để pha các dung dịch có tính kiềm như nước rửa xe ô tô không chạm. Rất tiện lợi cho việc chăm sóc xe tại gia đình. Ngoài ra, bình còn được sử dụng để rửa, làm sạch và khử trùng các bề mặt như sàn, tường, mặt tiền trong sảnh sản xuất, nhà kho, cơ sở công nghiệp.
Nó được chứng minh hoàn toàn tốt trong việc tẩy dầu mỡ cho các dụng cụ và động cơ, cũng như loại bỏ dầu, mỡ và muội than trong nhà bếp công nghiệp.
ĐẶC TRƯNG:
SẢN PHẦM ĐI KÈM CÓ 3 ĐẦU TẠO ĐỘ BỌT ĐỂ DỄ DÀNG LỰA CHỌN KHI SỬ DỤNG: BỌT ƯỚT; BỌT TRUNG; VÀ BỌT TUYẾT KHÔ
CÓ VAN TAN TOÀN - ÁP SUẤT LUÔN ĐƯỢC KIỂM SOÁT
TAY CẦM TIỆN LỢI - LÀM VIỆC THOẢI MÁI
DẢI CHẤT LỎNG NHÌN THẤY - DỄ DÀNG THEO DÕI MỨC CHẤT LỎNG
VÒNG ĐẾ - ỔN ĐỊNH VÀ BẢO VỆ
MỐI NỐI EDPM
Thông số kỹ thuật: capacity (l):Dung tích - 2L   pressure (bar):Áp lực: 2.2 bar   catalogue no.:Số hiệu catalogue: WTV.1186   Liquid flows out itself when pumping
Reason:
Absence or damage of "plug" gasket
Solution:
Unscrew the spraying tip from the pump body and check if the plug gasket is present in it; also check for damage or improper sitting. Replace in case of damage or absence.
 
Presence of liquid from the tank in the cylinder
Reason:
Damaged pump valve head.
Edges of the pump valve head soiled.
Solution:
Unscrew the pump from the head and check the condition of the pump valve head. Failure to adhere to the cylinder bottom, cracks, swelling or shrinkage of the gasket are symptoms of its damage. Replace it with a new one.
Dirt accumulated beneath the gasket edge may cause leakage. The problem should be eliminated after cleaning.
 
Problems with pumping, pump is letting liquid through
Reason:
Piston o-ring damaged.
No silicone oil on the o-ring surface
Solution:
Screw the pump off the sprayer head. Then, disassemble the pump by screwing out the pump body. After disassembly, inspect the o-ring for damage. If the o-ring is cracked or deformed, replace it.
After unscrewing the pump body, check if the o-ring is greased. In case of absence of silicone oil on the o-ring surface, grease it with silicone oil. After reassembling the pump, the device should operate correctly.
 
Inconsistent spray jet
Reason:
Damaged, clogged or improperly installed spraying tip.
Solution:
Unscrew the spraying nut and rinse it under running water. After reassembling, the nozzle should operate correctly. In case of permanent nozzle damage (miscalibration of the sprayer opening), replace the spraying tip with a new one.
 
Noticeable pressure decrease in the sprayer; safety valve fails to open or close, tank pressure falling
Reason:
Damaged safety valve.
Damaged sprayer head gasket.
Wrongly screwed sprayer pump or absence of gasket on the pump body.
Solution:
With the valve stem pulled aside, introduce several drops of silicone oil and open/close the valve several times. If the problem persists, replace the valve with a new one.
Check for presence of sealing element under the head (pump). Install a new one if absent; in case of damage (cutting, deformation), replace it with a new one.
Check that the o-ring on the pump body is not cut or damaged. In case of missing gasket under the pump body, install a new one or replace it if damaged.
 
Sprayer is spraying air instead of liquid
Reason:
The suction tube fell out of the fixing hole in the head body.
Solution:
Unscrew the sprayer head and insert the suction tube correctly by rotating until stop.
 
Liquid leaking from beneath the sprayer handle
Reason:
Damaged o-ring on the cut-off mandrel.
Faulty assembly of elements on the cut-off mandrel.
Solution:
With the spraying tip unscrewed and the "plug" gasket disassembled, introduce several drops of silicone oil into the hole on the head body and press the cut-off valve lever several times. If the problem persists, replace the cut-off mandrel with a new one.
Disassemble the mandrel assembly by removing it, and then place in the proper order (see manual).
seals: EPDM
 
Professional technical sprayersVenus Super Foamer HD alka line Foamer with the capacity 2L. It is used for washing, cleaning and disinfection of surfaces such as floors, walls, facades in production halls, warehouses, industrial facilities. It proves perfectly well in degreasing tools and motors, as also removing oils, grease and soot in industrial kitchens.
FEATURES:
3 foam endings in the set - for wet faom, medium foam and snow foam
safety valve – pressure always under control
convenient handle – work comfortably
visible fluid strip – easy to keep an eye on the fluid level
base ring – stabilization and protection
EPDM seals
Specifications capacity (l): 2     pressure (bar): 2,2   p catalogue no.: WTV.1186     EAN: 5904447006746   seals: EPDM Giá sản phẩm trên Tiki đã bao gồm thuế theo luật hiện hành. Bên cạnh đó, tuỳ vào loại sản phẩm, hình thức và địa chỉ giao hàng mà có thể phát sinh thêm chi phí khác như phí vận chuyển, phụ phí hàng cồng kềnh, thuế nhập khẩu (đối với đơn hàng giao từ nước ngoài có giá trị trên 1 triệu đồng).....